The N series uses a block-and-pin design with greater running clearance than the S series and a manganese phosphate coating. KYOWA lists agricultural equipment, mowers and vehicle mechanisms among its applications. NC is a single joint, ND is double, and NP uses an intermediate sliding spline.
Selection and application
Check the angle-adjusted speed and the combined selection index for NC and ND as well as their individual limits. For NP, compare the installed length and required travel with the relevant spline configuration. Check lubrication and environment for the specific installation.
Catalog configurations
| Type | End and shaft options |
|---|---|
| NC | 00A and 05A; rubber boot where listed. |
| ND | 00A and 05A; rubber boot where listed. |
| NP | 00A standard intermediate spline shaft. |
NC selection ratings
| Model | Allowable selection index | Allowable speed (rpm) | Allowable angle (°) | Allowable torque (N·m) | Static failure torque (N·m) | Static tensile failure load (N) | GD² (kg·cm²) | Mass (g) |
|---|---|---|---|---|---|---|---|---|
| NC-06-00 | 28,000 | 1,800 | 30 | 5.3 | 16 | 5,300 | 0.015 | 15 |
| NC-08-00 | 42,000 | 1,500 | 30 | 11.6 | 35 | 7,840 | 0.044 | 30 |
| NC-10-00 | 70,000 | 1,300 | 30 | 27.4 | 83 | 13,000 | 0.13 | 55 |
| NC-12-00 | 106,000 | 1,100 | 30 | 46 | 140 | 23,000 | 0.35 | 110 |
| NC-14-00 | 133,000 | 1,000 | 30 | 66 | 200 | 26,000 | 0.67 | 155 |
| NC-16-00 | 175,000 | 900 | 30 | 102 | 310 | 39,000 | 1.5 | 260 |
| NC-18-00 | 203,000 | 800 | 30 | 132 | 400 | 44,000 | 2.3 | 345 |
| NC-20-00 | 239,000 | 700 | 30 | 175 | 530 | 52,000 | 3.6 | 465 |
| NC-22-00 | 302,000 | 650 | 30 | 251 | 760 | 68,000 | 5.9 | 630 |
| NC-25-00 | 356,000 | 600 | 30 | 330 | 1,000 | 81,000 | 9.7 | 790 |
| NC-30-00 | 465,000 | 550 | 30 | 495 | 1,500 | 100,000 | 20 | 1,160 |
NC speed correction by angle
| Angle | ≤5° | 10° | 15° | 20° | 25° | 30° |
|---|---|---|---|---|---|---|
| Angle factor | 1.00 | 1.05 | 1.18 | 1.43 | 1.82 | 2.50 |
NC dimensions and limits (linear values in mm)
| Model | d | D | LC | l | C | E | LD | A | P | KC | KD |
|---|---|---|---|---|---|---|---|---|---|---|---|
| NC-06-**A | 6 | 12 | 31 | 15.5 | 9 | 4.5 | 49.5 | 18.5 | 3 | — | — |
| NC-08-**A | 8 | 15 | 36 | 18 | 10 | 5 | 58 | 22 | 3.5 | 25 | 26 |
| NC-10-**A | 10 | 20 | 42 | 21 | 12 | 6 | 67.5 | 25.5 | 4.5 | 32 | 32 |
| NC-12-**A | 12 | 23 | 52 | 26 | 15 | 7.5 | 83 | 31 | 5 | 35 | 36 |
| NC-14-**A | 14 | 26 | 59 | 29.5 | 17 | 8.5 | 94.5 | 35.5 | 5.8 | 40 | 40 |
| NC-16-**A | 16 | 30 | 74 | 37 | 22 | 11 | 117.5 | 43.5 | 6.5 | 46 | 46 |
| NC-18-**A | 18 | 33 | 81 | 40.5 | 23.5 | 11.75 | 129 | 48 | 7 | 52 | 52 |
| NC-20-**A | 20 | 36 | 87 | 43.5 | 25 | 12.5 | 139 | 52 | 8 | 58 | 58 |
| NC-22-**A | 22 | 40 | 94 | 47 | 27 | 13.5 | 150 | 56 | 9 | 62 | 62 |
| NC-25-**A | 25 | 44 | 105 | 52.5 | 30 | 15 | 168 | 63 | 10 | 68 | 68 |
| NC-30-**A | 30 | 51 | 122 | 61 | 35 | 17.5 | 195 | 73 | 11.5 | 82 | 82 |
ND selection ratings
| Model | Allowable selection index | Allowable speed (rpm) | Allowable angle (°) | Allowable torque (N·m) | Static failure torque (N·m) | Static tensile failure load (N) | GD² (kg·cm²) | Mass (g) |
|---|---|---|---|---|---|---|---|---|
| ND-06-00 | 28,000 | 1,800 | 30 per side | 3.96 | 12 | 5,300 | 0.029 | 30 |
| ND-08-00 | 42,000 | 1,500 | 30 per side | 8.58 | 26 | 7,840 | 0.069 | 50 |
| ND-10-00 | 70,000 | 1,300 | 30 per side | 20.1 | 61 | 13,000 | 0.21 | 95 |
| ND-12-00 | 106,000 | 1,100 | 30 per side | 33 | 100 | 23,000 | 0.55 | 180 |
| ND-14-00 | 133,000 | 1,000 | 30 per side | 46 | 140 | 26,000 | 1.0 | 250 |
| ND-16-00 | 175,000 | 900 | 30 per side | 76 | 230 | 39,000 | 2.3 | 410 |
| ND-18-00 | 203,000 | 800 | 30 per side | 96 | 290 | 44,000 | 3.7 | 550 |
| ND-20-00 | 239,000 | 700 | 30 per side | 129 | 390 | 52,000 | 5.7 | 690 |
| ND-22-00 | 302,000 | 650 | 30 per side | 185 | 560 | 68,000 | 9.1 | 940 |
| ND-25-00 | 356,000 | 600 | 30 per side | 248 | 750 | 81,000 | 15 | 1,240 |
| ND-30-00 | 465,000 | 550 | 30 per side | 363 | 1,100 | 100,000 | 31 | 1,775 |
ND dimensions and limits (linear values in mm)
| Model | d | D | LC | l | C | E | LD | A | P | KC | KD |
|---|---|---|---|---|---|---|---|---|---|---|---|
| ND-06-**A | 6 | 12 | 31 | 15.5 | 9 | 4.5 | 49.5 | 18.5 | 3 | — | — |
| ND-08-**A | 8 | 15 | 36 | 18 | 10 | 5 | 58 | 22 | 3.5 | 25 | 26 |
| ND-10-**A | 10 | 20 | 42 | 21 | 12 | 6 | 67.5 | 25.5 | 4.5 | 32 | 32 |
| ND-12-**A | 12 | 23 | 52 | 26 | 15 | 7.5 | 83 | 31 | 5 | 35 | 36 |
| ND-14-**A | 14 | 26 | 59 | 29.5 | 17 | 8.5 | 94.5 | 35.5 | 5.8 | 40 | 40 |
| ND-16-**A | 16 | 30 | 74 | 37 | 22 | 11 | 117.5 | 43.5 | 6.5 | 46 | 46 |
| ND-18-**A | 18 | 33 | 81 | 40.5 | 23.5 | 11.75 | 129 | 48 | 7 | 52 | 52 |
| ND-20-**A | 20 | 36 | 87 | 43.5 | 25 | 12.5 | 139 | 52 | 8 | 58 | 58 |
| ND-22-**A | 22 | 40 | 94 | 47 | 27 | 13.5 | 150 | 56 | 9 | 62 | 62 |
| ND-25-**A | 25 | 44 | 105 | 52.5 | 30 | 15 | 168 | 63 | 10 | 68 | 68 |
| ND-30-**A | 30 | 51 | 122 | 61 | 35 | 17.5 | 195 | 73 | 11.5 | 82 | 82 |
NP dimensions and limits (linear values in mm)
| Model | d | L | Axial travel | A | B | Spline specification S | E | LC | LQ | D | F | G | H | J |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| NP-08-00A | 8 | 163 | +19 -11 | 127 | 65 | Involute spline Major dia.=10 m=0.75 z=11 | 20 | 36 | — | 17 | 11 | 39 | 65 | 26 |
| NP-10-00A | 10 | 177 | +17 -13 | 135 | 65 | Involute spline Major dia.=12 m=1.0 z=10 | 25 | 42 | 42 | 19 | 13 | 37 | 65 | 28 |
| NP-12-00A | 12 | 225 | +16 -16 | 173 | 88 | Straight-sided spline 16×13×3.5-6 | 40 | 52 | 52 | 23 | 16 | 56 | 89 | 32 |
| NP-14-00A | 14 | 240 | +14 -18 | 181 | 87 | Straight-sided spline 16×13×3.5-6 | 40 | 59 | 59 | 23 | 18 | 54 | 89 | 33 |
| NP-16-00A | 16 | 308 | +35 -23 | 234 | 115 | Straight-sided spline 20×16×4-6 | 40 | 74 | 74 | 30 | 23 | 75 | 120 | 40 |
| NP-18-00A | 18 | 327 | +30 -26 | 246 | 115 | Straight-sided spline 20×16×4-6 | 40 | 81 | 81 | 30 | 26 | 70 | 120 | 45 |
| NP-20-00A | 20 | 344 | +33 -27 | 257 | 118 | Straight-sided spline 22×18×5-6 | 40 | 87 | 87 | 36 | 27 | 73 | 125 | 45 |
| NP-22-00A | 22 | 360 | +28 -30 | 266 | 115 | Straight-sided spline 25×21×5-6 | 40 | 94 | 94 | 40 | 30 | 68 | 125 | 47 |
| NP-25-00A | 25 | 405 | +38 -32 | 300 | 133 | Straight-sided spline 28×23×6-6 | 45 | 105 | 105 | 44 | 32 | 83 | 145 | 50 |
| NP-30-00A | 30 | 464 | +35 -40 | 342 | 145 | Straight-sided spline 32×26×6-6 | 50 | 122 | 122 | 51 | 40 | 85 | 160 | 60 |
Product images and drawings



