The S series uses a compact block-and-pin construction with low backlash. The main parts are carburized SCM415. SC is a single joint, SD is a double joint, and SP adds an intermediate sliding spline. Typical applications include printing, multispindle drilling and sheet leveling.
Selection and application
Check the allowable torque, angle and speed together. For SC and SD the catalog uses speed × working angle × torque as a selection index, and multiplies actual speed by the angle factor for the speed check. A dash denotes an unlisted value. Double-joint angles apply to each side where indicated. Confirm the installed length and working stroke for SP.
Catalog configurations
| Type | End and shaft options |
|---|---|
| SC | 00A pin; 03A and 33A newer JIS key; 08A and 88A older JIS key; 09A quick-change; optional rubber cover on eligible configurations. |
| SD | 00A pin; 03A and 33A newer JIS key; 08A and 88A older JIS key; rubber cover where listed. |
| SP | 00A, 03A, 33A, 08A, 88A, 09A and 99A options; check eligible sizes and the exact end combination. |
SC selection ratings
| Model | Allowable selection index | Allowable speed (rpm) | Allowable angle (°) | Allowable torque (N·m) | Static failure torque (N·m) | Static tensile failure load (N) | GD² (kg·cm²) | Mass (g) |
|---|---|---|---|---|---|---|---|---|
| SC-03-00A | 8,000 | 4,000 | 30 | 0.13 | 0.4 | 680 | 0.001 | 5 |
| SC-04-00A | 13,000 | 3,300 | 30 | 0.96 | 2.9 | 1,200 | 0.003 | 8 |
| SC-05-00A | 21,000 | 2,800 | 30 | 3.23 | 9.8 | 2,000 | 0.007 | 12 |
| SC-06-** | 32,000 | 2,500 | 30 | 5.3 | 16 | 5,300 | 0.015 | 15 |
| SC-08-** | 48,000 | 2,200 | 30 | 11.6 | 35 | 7,840 | 0.044 | 30 |
| SC-10-** | 80,000 | 2,000 | 30 | 27.4 | 83 | 13,000 | 0.13 | 55 |
| SC-12-** | 121,000 | 1,800 | 30 | 46 | 140 | 23,000 | 0.35 | 110 |
| SC-14-** | 151,000 | 1,600 | 30 | 66 | 200 | 26,000 | 0.67 | 155 |
| SC-16-** | 200,000 | 1,400 | 30 | 102 | 310 | 39,000 | 1.5 | 260 |
| SC-18-** | 232,000 | 1,200 | 30 | 132 | 400 | 44,000 | 2.3 | 345 |
| SC-20-** | 273,000 | 1,000 | 30 | 175 | 530 | 52,000 | 3.6 | 465 |
| SC-22-** | 344,000 | 900 | 30 | 251 | 760 | 68,000 | 5.9 | 630 |
| SC-25-** | 406,000 | 800 | 30 | 330 | 1,000 | 81,000 | 9.7 | 790 |
| SC-30-** | 531,000 | 700 | 30 | 495 | 1,500 | 100,000 | 20 | 1,160 |
| SC-35-** | 711,000 | 600 | 30 | 792 | 2,400 | 140,000 | 41 | 2,255 |
| SC-40-** | 918,000 | 500 | 30 | 1,188 | 3,600 | 180,000 | 77 | 2,730 |
| SC-45-** | 1,150,000 | 400 | 30 | 1,584 | 4,800 | 220,000 | 130 | 4,350 |
| SC-50-** | 1,400,000 | 300 | 30 | 1,914 | 5,800 | 280,000 | 220 | 5,200 |
SC speed correction by angle
| Angle | ≤5° | 10° | 15° | 20° | 25° | 30° |
|---|---|---|---|---|---|---|
| Angle factor | 1.00 | 1.05 | 1.18 | 1.43 | 1.82 | 2.50 |
SC dimensions and limits (linear values in mm)
| Model | d | D | LC | l | C | E | P | b | t | b8 | t8 | M | KC |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| SC-03-00A | 3 | 6 | 26 | 13 | 9 | 2.5 | 1 | — | — | — | — | — | — |
| SC-04-00A | 4 | 8 | 24 | 12 | 7 | 4 | 1.5 | — | — | — | — | — | — |
| SC-05-00A | 5 | 10 | 30 | 15 | 9 | 5 | 2 | — | — | — | — | — | — |
| SC-06-**A | 6 | 12 | 31 | 15.5 | 9 | 4.5 | 3 | — | — | — | — | 3 | — |
| SC-08-**A | 8 | 15 | 36 | 18 | 10 | 5 | 3.5 | — | — | — | — | 3 | 25 |
| SC-10-**A | 10 | 19 | 42 | 21 | 12 | 6 | 4.5 | 3 | 11.4 | 4 | 11.5 | 5 | 32 |
| SC-12-**A | 12 | 23 | 52 | 26 | 15 | 7.5 | 5 | 4 | 13.8 | 4 | 13.5 | 5 | 35 |
| SC-14-**A | 14 | 26 | 59 | 29.5 | 17 | 8.5 | 5.8 | 5 | 16.3 | 5 | 16 | 6 | 40 |
| SC-16-**A | 16 | 30 | 74 | 37 | 22 | 11 | 6.5 | 5 | 18.3 | 5 | 18 | 6 | 46 |
| SC-18-**A | 18 | 33 | 81 | 40.5 | 23.5 | 11.75 | 7 | 6 | 20.8 | 5 | 20 | 6 | 52 |
| SC-20-**A | 20 | 36 | 87 | 43.5 | 25 | 12.5 | 8 | 6 | 22.8 | 5 | 22 | 6 | 58 |
| SC-22-**A | 22 | 40 | 94 | 47 | 27 | 13.5 | 9 | 6 | 24.8 | 7 | 25 | 6 | 62 |
| SC-25-**A | 25 | 44 | 105 | 52.5 | 30 | 15 | 10 | 8 | 28.3 | 7 | 28 | 8 | 68 |
| SC-30-**A | 30 | 51 | 122 | 61 | 35 | 17.5 | 11.5 | 8 | 33.3 | 7 | 33 | 8 | 82 |
| SC-35-**A | 35 | 59 | 140 | 70 | 40 | 20 | 13 | 10 | 38.3 | 10 | 38.5 | 10 | 90 |
| SC-40-**A | 40 | 67 | 157 | 78.5 | 45 | 22.5 | 14.5 | 12 | 43.3 | 10 | 43.5 | 10 | 100 |
| SC-45-**A | 45 | 75 | 176 | 88 | 50 | 25 | 16 | 14 | 48.8 | 12 | 48.5 | 10 | 110 |
| SC-50-**A | 50 | 83 | 191 | 95.5 | 55 | 27.5 | 17.5 | 14 | 53.8 | 12 | 53.5 | 10 | 120 |
SC quick-change dimensions (mm)
| Model | d | D | LQ | l | C | E | P | DQ | CQ | EQ | I | R | JQ | bQ | tQ | KQ |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| SC-08-09A | 8 | 15 | 38 | 18 | 10 | 5 | 3.5 | 19 | 12 | 4 | 6.56 | 2 | 8 | 3 | 5.8 | 10 |
| SC-10-09A | 10 | 19 | 42 | 21 | 12 | 6 | 4.5 | 21.5 | 12 | 4 | 9.06 | 2 | 8 | 4 | 7.5 | 9 |
| SC-12-09A | 12 | 23 | 52 | 26 | 15 | 7.5 | 5 | 23.8 | 15 | 7.5 | 10.48 | 2.4 | 7.5 | 4 | 8.8 | 12 |
| SC-14-09A | 14 | 26 | 59 | 29.5 | 17 | 8.5 | 5.8 | 29 | 17 | 8.5 | 11.88 | 2.8 | 8.5 | 5 | 10.3 | 14 |
| SC-16-09A | 16 | 30 | 74 | 37 | 22 | 11 | 6.5 | 35 | 22 | 11 | 13.3 | 3.2 | 11 | 5 | 12.3 | 18 |
| SC-18-09A | 18 | 33 | 81 | 40.5 | 23.5 | 11.75 | 7 | 38 | 23.5 | 11.75 | 15.3 | 3.2 | 11.75 | 5 | 14.5 | 21 |
| SC-20-09A | 20 | 36 | 87 | 43.5 | 25 | 12.5 | 8 | 42 | 25 | 12.5 | 17.12 | 4 | 12.5 | 6 | 16.0 | 23 |
| SC-22-09A | 22 | 40 | 94 | 47 | 27 | 13.5 | 9 | 44 | 27 | 13.5 | 19.12 | 4 | 13.5 | 6 | 17.8 | 25 |
| SC-25-09A | 25 | 44 | 105 | 52.5 | 30 | 15 | 10 | 49 | 30 | 15 | 21.54 | 4.4 | 15 | 7 | 21 | 28 |
| SC-30-09A | 30 | 51 | 122 | 61 | 35 | 17.5 | 11.5 | 56 | 35 | 17.5 | 26.95 | 4.8 | 17.5 | 7 | 25.3 | 30 |
SD selection ratings
| Model | Allowable selection index | Allowable speed (rpm) | Allowable angle (°) | Allowable torque (N·m) | Static failure torque (N·m) | Static tensile failure load (N) | GD² (kg·cm²) | Mass (g) |
|---|---|---|---|---|---|---|---|---|
| SD-06-** | 32,000 | 2,500 | 30 per side | 3.96 | 12 | 5,300 | 0.029 | 30 |
| SD-08-** | 48,000 | 2,200 | 30 per side | 8.58 | 26 | 7,840 | 0.069 | 50 |
| SD-10-** | 80,000 | 2,000 | 30 per side | 20.1 | 61 | 13,000 | 0.21 | 95 |
| SD-12-** | 121,000 | 1,800 | 30 per side | 33 | 100 | 23,000 | 0.55 | 180 |
| SD-14-** | 151,000 | 1,600 | 30 per side | 46 | 140 | 26,000 | 1.0 | 250 |
| SD-16-** | 200,000 | 1,400 | 30 per side | 76 | 230 | 39,000 | 2.3 | 410 |
| SD-18-** | 232,000 | 1,200 | 30 per side | 96 | 290 | 44,000 | 3.7 | 550 |
| SD-20-** | 273,000 | 1,000 | 30 per side | 129 | 390 | 52,000 | 5.7 | 690 |
| SD-22-** | 344,000 | 900 | 30 per side | 185 | 560 | 68,000 | 9.1 | 940 |
| SD-25-** | 406,000 | 800 | 30 per side | 248 | 750 | 81,000 | 15 | 1,240 |
| SD-30-** | 531,000 | 700 | 30 per side | 363 | 1,100 | 100,000 | 31 | 1,775 |
| SD-35-** | 711,000 | 600 | 30 per side | 594 | 1,800 | 140,000 | 75 | 3,180 |
| SD-40-** | 918,000 | 500 | 30 per side | 891 | 2,700 | 180,000 | 120 | 4,150 |
| SD-45-** | 1,150,000 | 400 | 30 per side | 1,155 | 3,500 | 220,000 | 210 | 6,225 |
| SD-50-** | 1,400,000 | 300 | 30 per side | 1,419 | 4,300 | 280,000 | 340 | 7,750 |
SD dimensions and limits (linear values in mm)
| Model | d | D | LD | A | l | C | E | P | b | t | b8 | t8 | M | KD |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| SD-06-**A | 6 | 12 | 49.5 | 18.5 | 15.5 | 9 | 4.5 | 3 | — | — | — | — | 3 | — |
| SD-08-**A | 8 | 15 | 58 | 22 | 18 | 10 | 5 | 3.5 | — | — | — | — | 3 | 26 |
| SD-10-**A | 10 | 19 | 67.5 | 25.5 | 21 | 12 | 6 | 4.5 | 3 | 11.4 | 4 | 11.5 | 5 | 32 |
| SD-12-**A | 12 | 23 | 83 | 31 | 26 | 15 | 7.5 | 5 | 4 | 13.8 | 4 | 13.5 | 5 | 36 |
| SD-14-**A | 14 | 26 | 94.5 | 35.5 | 29.5 | 17 | 8.5 | 5.8 | 5 | 16.3 | 5 | 16 | 6 | 40 |
| SD-16-**A | 16 | 30 | 117.5 | 43.5 | 37 | 22 | 11 | 6.5 | 5 | 18.3 | 5 | 18 | 6 | 46 |
| SD-18-**A | 18 | 33 | 129 | 48 | 40.5 | 23.5 | 11.75 | 7 | 6 | 20.8 | 5 | 20 | 6 | 52 |
| SD-20-**A | 20 | 36 | 139 | 52 | 43.5 | 25 | 12.5 | 8 | 6 | 22.8 | 5 | 22 | 6 | 58 |
| SD-22-**A | 22 | 40 | 150 | 56 | 47 | 27 | 13.5 | 9 | 6 | 24.8 | 7 | 25 | 6 | 62 |
| SD-25-**A | 25 | 44 | 168 | 63 | 52.5 | 30 | 15 | 10 | 8 | 28.3 | 7 | 28 | 8 | 68 |
| SD-30-**A | 30 | 51 | 195 | 73 | 61 | 35 | 17.5 | 11.5 | 8 | 33.3 | 7 | 33 | 8 | 82 |
| SD-35-**A | 35 | 59 | 224 | 84 | 70 | 40 | 20 | 13 | 10 | 38.3 | 10 | 38.5 | 10 | 90 |
| SD-40-**A | 40 | 67 | 251 | 94 | 78.5 | 45 | 22.5 | 14.5 | 12 | 43.3 | 10 | 43.5 | 10 | 100 |
| SD-45-**A | 45 | 75 | 282 | 106 | 88 | 50 | 25 | 16 | 14 | 48.8 | 12 | 48.5 | 10 | 110 |
| SD-50-**A | 50 | 83 | 304 | 113 | 95.5 | 55 | 27.5 | 17.5 | 14 | 53.8 | 12 | 53.5 | 10 | 120 |
SP dimensions and limits (linear values in mm)
| Model | d | L | Axial travel | A | B | Spline specification S | E | LC | LQ | D | F | G | H | J |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| SP-08-**A | 8 | 163 | +19 -11 | 127 | 65 | Involute spline Major dia.=10 m=0.75 z=11 | 20 | 36 | — | 17 | 11 | 39 | 65 | 26 |
| SP-08-09A | 8 | 167 | +17 -13 | 129 | 65 | Involute spline Major dia.=10 m=0.75 z=11 | 20 | 36 | 38 | 17 | 13 | 37 | 65 | 28 |
| SP-08-99A | 8 | 169 | +17 -13 | 129 | 65 | Involute spline Major dia.=10 m=0.75 z=11 | 20 | — | 38 | 17 | 13 | 37 | 65 | 28 |
| SP-10-**A | 10 | 177 | +17 -13 | 135 | 65 | Involute spline Major dia.=12 m=1.0 z=10 | 25 | 42 | 42 | 19 | 13 | 37 | 65 | 28 |
| SP-12-**A | 12 | 225 | +16 -16 | 173 | 88 | Straight-sided spline 16×13×3.5-6 | 40 | 52 | 52 | 23 | 16 | 56 | 89 | 32 |
| SP-14-**A | 14 | 240 | +14 -18 | 181 | 87 | Straight-sided spline 16×13×3.5-6 | 40 | 59 | 59 | 23 | 18 | 54 | 89 | 33 |
| SP-16-**A | 16 | 308 | +35 -23 | 234 | 115 | Straight-sided spline 20×16×4-6 | 40 | 74 | 74 | 30 | 23 | 75 | 120 | 40 |
| SP-18-**A | 18 | 327 | +30 -26 | 246 | 115 | Straight-sided spline 20×16×4-6 | 40 | 81 | 81 | 30 | 26 | 70 | 120 | 45 |
| SP-20-**A | 20 | 344 | +33 -27 | 257 | 118 | Straight-sided spline 22×18×5-6 | 40 | 87 | 87 | 36 | 27 | 73 | 125 | 45 |
| SP-22-**A | 22 | 360 | +28 -30 | 266 | 115 | Straight-sided spline 25×21×5-6 | 40 | 94 | 94 | 40 | 30 | 68 | 125 | 47 |
| SP-25-**A | 25 | 405 | +38 -32 | 300 | 133 | Straight-sided spline 28×23×6-6 | 45 | 105 | 105 | 44 | 32 | 83 | 145 | 50 |
| SP-30-**A | 30 | 464 | +35 -40 | 342 | 145 | Straight-sided spline 32×26×6-6 | 50 | 122 | 122 | 51 | 40 | 85 | 160 | 60 |
| SP-35-**A | 35 | 515 | +35 -45 | 375 | 150 | Involute spline 35×19×1.667 | 50 | 140 | — | 55 | 45 | 85 | 170 | 65 |
| SP-40-**A | 40 | 574 | +35 -50 | 417 | 165 | Involute spline 40×22×1.667 | 60 | 157 | — | 65 | 50 | 95 | 190 | 70 |
| SP-45-**A | 45 | 637 | +35 -55 | 461 | 180 | Involute spline 45×25×1.667 | 70 | 176 | — | 75 | 55 | 105 | 210 | 75 |
| SP-50-**A | 50 | 697 | +35 -60 | 506 | 200 | Involute spline 50×28×1.667 | 80 | 191 | — | 83 | 60 | 115 | 230 | 85 |
Product images and drawings



